H3C交换机RRPP配置

配置Device A

# 创建VLAN 2～30，将这些VLAN都映射到MSTI 1上，并激活MST域的配置。

<DeviceA> system-view

[DeviceA] vlan 2 to 30

 Please wait… Done.

[DeviceA] stp region-configuration

[DeviceA-mst-region] instance 1 vlan 2 to 30

[DeviceA-mst-region] active region-configuration

[DeviceA-mst-region] quit

# 分别在端口GigabitEthernet1/0/1和GigabitEthernet1/0/2上关闭STP功能，配置端口信任报文的802.1p优先级，并将端口配置为Trunk端口且允许VLAN 2～30通过。

[DeviceA] interface gigabitethernet 1/0/1

[DeviceA-GigabitEthernet1/0/1] undo stp enable

[DeviceA-GigabitEthernet1/0/1] port link-type trunk

[DeviceA-GigabitEthernet1/0/1] port trunk permit vlan 2 to 30

 Please wait… Done.

[DeviceA-GigabitEthernet1/0/1] quit

[DeviceA] interface gigabitethernet 1/0/2

[DeviceA-GigabitEthernet1/0/2] undo stp enable

[DeviceA-GigabitEthernet1/0/2] port link-type trunk

[DeviceA-GigabitEthernet1/0/2] port trunk permit vlan 2 to 30

 Please wait… Done.

[DeviceA-GigabitEthernet1/0/2] quit

# 创建RRPP域1，将VLAN 4092配置为该域的控制VLAN，并将MSTI 1所映射的VLAN配置为该域的保护VLAN。

[DeviceA] rrpp domain 1

 Info: Create a new domain.

[DeviceA-rrpp-domain1] control-vlan 4092

[DeviceA-rrpp-domain1] protected-vlan reference-instance 1

# 配置本设备为主环1的主节点，主端口为GigabitEthernet1/0/1，副端口为GigabitEthernet1/0/2，并开启该环。

[DeviceA-rrpp-domain1] ring 1 node-mode master primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 0

[DeviceA-rrpp-domain1] ring 1 enable

[DeviceA-rrpp-domain1] quit

# 开启RRPP协议。

[DeviceA] rrpp enable

(2) 配置Device B

# 创建VLAN 2～30，将这些VLAN都映射到MSTI 1上，并激活MST域的配置。

<DeviceB> system-view

[DeviceB] vlan 2 to 30

 Please wait… Done.

[DeviceB] stp region-configuration

[DeviceB-mst-region] instance 1 vlan 2 to 30

[DeviceB-mst-region] active region-configuration

[DeviceB-mst-region] quit

# 分别在端口GigabitEthernet1/0/1和GigabitEthernet1/0/2上关闭STP功能，配置端口信任报文的802.1p优先级，并将端口配置为Trunk端口且允许VLAN 2～30通过。

[DeviceB] interface gigabitethernet 1/0/1

[DeviceB-GigabitEthernet1/0/1] undo stp enable

[DeviceB-GigabitEthernet1/0/1] qos trust dot1p

[DeviceB-GigabitEthernet1/0/1] port link-type trunk

[DeviceB-GigabitEthernet1/0/1] port trunk permit vlan 2 to 30

 Please wait… Done.

[DeviceB-GigabitEthernet1/0/1] quit

[DeviceB] interface gigabitethernet 1/0/2

[DeviceB-GigabitEthernet1/0/2] undo stp enable

[DeviceB-GigabitEthernet1/0/2] qos trust dot1p

[DeviceB-GigabitEthernet1/0/2] port link-type trunk

[DeviceB-GigabitEthernet1/0/2] port trunk permit vlan 2 to 30

 Please wait… Done.

[DeviceB-GigabitEthernet1/0/2] quit

# 创建RRPP域1，将VLAN 4092配置为该域的控制VLAN，并将MSTI 1所映射的VLAN配置为该域的保护VLAN。

[DeviceB] rrpp domain 1

 Info: Create a new domain.

[DeviceB-rrpp-domain1] control-vlan 4092

[DeviceB-rrpp-domain1] protected-vlan reference-instance 1

# 配置本设备为主环1的传输节点，主端口为GigabitEthernet1/0/1，副端口为GigabitEthernet1/0/2，并开启该环。

[DeviceB-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 0

[DeviceB-rrpp-domain1] ring 1 enable

[DeviceB-rrpp-domain1] quit

# 开启RRPP协议。

[DeviceB] rrpp enable

(3) 配置Device C和Device D

Device C、Device D的配置与Device B完全相同，配置过程略。

猜你喜欢