我学习了华为基本的路由交换技术和简单的配置方法,所以网上找了一份实训题进行训练,里面会有错误,当然也有我不会配置的,今天分享上来是想与大家交流与学习。希望有大牛能够
给予指正。
一、基本配置
为R1-R2-R3-R4-R5配置Loopback接口,编号均为0。
操作步骤: [R1]interface LoopBack 0
[R1-LoopBack0]ip add 10.1.1.1 24
[R2]interface LoopBack 0
[R2-LoopBack0]ip add 10.1.2.2 24
[R3]interfaceLoopBack 0
[R3-LoopBack0]ipadd 10.1.3.3 24
[R4]interfaceLoopBack 0
[R4-LoopBack0]ip add 10.1.4.4 24
[R5]interfaceLoopBack 0
[R5-LoopBack0]ip add 10.1.5.5 24
网络设备及终端:
192.168.10.2/24 |
||
PC7 |
192.168.10.3/24 |
|
PC3 |
192.168.20.2/24 |
|
PC4 |
192.168.20.3/24 |
|
PC5 |
173.16.1.1/24 |
|
Server1
|
173.16.1.2/24 |
|
R2 |
S0/0/2 |
10.0.2.2/24 |
G0/0/0 |
10.0.23.2/24 |
|
G0/0/1 |
10.0.24.1/24 |
|
R3 |
G0/0/0 |
10.0.23.3/24 |
G0/0/1 |
10.0.35.3/24 |
|
R4 |
G0/0/1 |
10.0.24.4/24 |
G0/0/2 |
10.0.45.4/24 |
|
R5 |
G0/0/1 |
10.0.35.5/24 |
G0/0/2 |
10.0.45.5/24 |
R1 S0/0/2 10.0.12.1/24
S0/0/2 10.0.12.2/24
IP地址已固定给出,请按要求完成配置。
二、配置VLAN。
1、PC1和PC7属于Vlan10,所属网络为192.168.10.0/24。
操作步骤:
创建
VLAN10
:
[S1]vlan 10
设置端口类型:
[S1-Ethernet0/0/2]port link-type access
[S1-Ethernet0/0/3]port link-type access
设置接口
PVID
:
[S1-Ethernet0/0/3]port default vlan 10
[S1-Ethernet0/0/3]port default vlan 10
二层与三层之间设置
Trunk
:
[S1-Ethernet0/0/3]int e0/0/4
[S1-Ethernet0/0/4]port link-type trunk
[S1-Ethernet0/0/4]port trunk allow-pass vlan all
2、PC1和PC7属于Vlan10,所属网络为192.168.20.0/24。
操作步骤:
创建
VLAN20
:
[S2]vlan 20
设置端口类型:
[S2-Ethernet0/0/2]port link-type access
[S2-Ethernet0/0/3]port link-type access
设置接口
PVID
:
[S2-Ethernet0/0/3]port default vlan 20
[S2-Ethernet0/0/3]port default vlan 20
设置二层与三层交换接口为
Trunk
型:
[S2-Ethernet0/0/3]int e0/0/4
[S2-Ethernet0/0/4]port link-type trunk
[S2-Ethernet0/0/4]port trunk allow-pass vlan all
3.PC5和Server属于Vlan1,所属网络为173.16.1.0/24,连接主机主机的接口均为Access接口。
操作步骤:
创建
VLAN1
:
[S1]vlan 1
设置端口类型:
[S5-Ethernet0/0/1]port link-type access
[S5-Ethernet0/0/2]port link-type access
设置接口
PVID:
[S5-Ethernet0/0/1]port default vlan 1
[S5-Ethernet0/0/2]port default vlan 1
三
、配置Eth-trunk(链路聚合)
SW3
与
SW4
创建
Eth-trunk 1
连接
SW3
GE0/0/1 GE0/0/2 GE0/0/3
操作步骤:
设置二层与三层交换接口为
Trunk
型:
[S3]int g0/0/4
[S3-GigabitEthernet0/0/4]portlink-type trunk
[S3-GigabitEthernet0/0/4]porttrunk allow-pass vlan all
[S3]int Eth-Trunk 1
[S3-Eth-Trunk1]mode manual
[S3-Eth-Trunk1]int g0/0/1
[S3-GigabitEthernet0/0/1]eth-trunk 1
[S3-GigabitEthernet0/0/1]int g0/0/2
[S3-GigabitEthernet0/0/2]eth-trunk 1
[S3-GigabitEthernet0/0/2]int g0/0/3
[S3-GigabitEthernet0/0/3]eth-trunk 1
SW4 GE0/0/1 GE0/0/7 GE0/0/8
操作步骤:
设置二层与三层交换接口为Trunk型:[S4]int g0/0/4
[S4-GigabitEthernet0/0/4]portlink-type trunk
[S4-GigabitEthernet0/0/4]porttrunk allow-pass vlan all
[S4]int Eth-Trunk 1
[S4-Eth-Trunk1]mode manual
[S4-Eth-Trunk1]int g0/0/1
[S4-GigabitEthernet0/0/1]eth-trunk 1
[S4-GigabitEthernet0/0/1]int g0/0/7
[S4-GigabitEthernet0/0/7]eth-trunk 1
[S4-GigabitEthernet0/0/7]int g0/0/8
[S4-GigabitEthernet0/0/8]eth-trunk 1
四、部署MSTP instance 1 和instance 2
SW3为instance 1的主要根桥,SW4为次要根桥
SW4为instance 2的主要根桥,SW3为次要根桥
VLAN10用户所属Instance1
操作步骤:
[S3]stp region-configuration
[S3-mst-region]region-name mst-region
[S3-mst-region]instance 1 vlan 10
[S3-mst-region]instance 2 vlan 20
[S3-mst-region]active region-configuration
[S3]stp instance 1 root primary
[S3]stp instance 2 root secondary
[S3-mst-region]check region-configuration
VLAN20用户所属Instance2
操作步骤:
[S4]stp region-configuration
[S4-mst-region]region-name mst-region
[S4-mst-region]instance 1 vlan 10
[S4-mst-region]instance 2 vlan 20
[S4-mst-region]active region-configuration
[S4]stp instance 1 root secondary
[S4]stp instance 2 root primary
[S4-mst-region]check region-configuration
五、配置单区域OSPF路由协议
1.
在路由器
R1-R2-R3-R4-R5
上配置
OSPF
(进程
ID
为
1
),
router id
为
Loopback 0
接口地址。
2.
将路由器上的所有对应网络宣告进
Area 0
中,包括
Loopback0(
排除
R1
与
SW3
、
SW4
之间的直连网段
)
。
配置方法:
[R1]ospf router-id 10.1.1.1
[R1-ospf-1]
area 0
[R1-ospf-1-area-0.0.0.0]network 10.0.12.0 0.0.0.255
[R1-ospf-1-area-0.0.0.0]network 10.1.1.0 0.0.0.255
[R2]ospf router-id 10.1.2.2
[R2-ospf-1]area 0
[R2-ospf-1-area-0.0.0.0]network 10.0.12.0 0.0.0.255
[R2-ospf-1-area-0.0.0.0]network 10.0.24.0 0.0.0.255
[R2-ospf-1-area-0.0.0.0]network 10.1.2.0 0.0.0.255
[R3]ospf router-id 10.1.3.3
[R3-ospf-1]area 0
[R3-ospf-1-area-0.0.0.0]network 10.0.23.0 0.0.0.255
[R3-ospf-1-area-0.0.0.0]network 10.0.35.0 0.0.0.255
[R3-ospf-1-area-0.0.0.0]network 10.1.3.0 0.0.0.255
[R4]ospf router-id 10.1.4.4
[R4-ospf-1]area 0
[R4-ospf-1-area-0.0.0.0]network 10.0.24.0 0.0.0.255
[R4-ospf-1-area-0.0.0.0]network 10.0.45.0 0.0.0.255
[R4-ospf-1-area-0.0.0.0]network 10.1.4.4 0.0.0.255
[R5]ospf router-id 10.1.5.5
[R5-ospf-1]area 0
[R5-ospf-1-area-0.0.0.0]network 10.0.35.0 0.0.0.255
[R5-ospf-1-area-0.0.0.0]network 10.0.45.0 0.0.0.255
[R5-ospf-1-area-0.0.0.0]network 10.1.5.5 0.0.0.255
六、OSPF调优
使用下列原则设置
OSPF
优先级:
R3
、
R4
绝不参与
DR/BDR
选举。
R2
始终将成为
DR
,并且优先级为最大值。
配置方法:
[R3]int g0/0/0
[R3-GigabitEthernet0/0/0]ospf dr-priority 0
[R3-GigabitEthernet0/0/0]int g0/0/1
[R3-GigabitEthernet0/0/1]ospf dr-priority 0
[R4]int g0/0/1
[R4-GigabitEthernet0/0/1]ospf dr-priority 0
[R4-GigabitEthernet0/0/1]int g0/0/2
[R4-GigabitEthernet0/0/2]ospf dr-priority 0
[R2]int g0/0/0
[R2-GigabitEthernet0/0/0]ospf dr-priority255
[R2-GigabitEthernet0/0/0]int g0/0/1
[R2-GigabitEthernet0/0/1]ospf dr-priority 255
七、部署RIPV2路由协议 (待解决,不知交换机上怎样配置RIP,请大家帮忙!)
1.
在设备
R1 SW3 SW4
上配置
RIPV2
(进程
ID
为
1
)。
2.
将设备上的所有对应网络宣告进
RIP
进程中。
八、路由发布。
1、
在
R1
将
RIP
路由发布到
OSPF
路由域中。
操作步骤:
[R1]rip
[R1-rip-1]version 2
[R1-rip-1]import-route ospf
2、
R1
设备发布默认路由到
SW3、SW4.
操作步骤:
[S3]ospf
[S3-ospf-1]import-route rip
[S4]ospf
[S4-ospf-1]import-route rip
九、网络可靠性部署VRRP
SW3
是
PC1 PC7
主
PC3 PC4
备份网关设备
物理地址
虚拟网关地址为:
Vlanif
10
:
Ip address
192.168.10.253/24
Vrrpvrid 1 virtual-ip
192.168.10.254
优先级
xx
关联上行端口并降低优先级
xx MD5
密码
huawei
抢占时延
xxS
(
20s
)
配置操作:
[S3]vlan batch 10 20
[S3-Vlanif10]ip ad 192.168.10.253 24
[S3-Vlanif10]vrrp vrid 1 virtual-ip 192.168.10.254
[S3-Vlanif10]vrrp vrid 1 priority 150
[S3-Vlanif10]vrrp vrid 2 virtual-ip 192.168.10.1
[S3-Vlanif10]vrrp vrid 2 priority 100
[S3-Vlanif10]vrrp vrid 1 track interface GigabitEthernet 0/0/6 reduced 100
[S3-Vlanif10]vrrp vrid 1 preempt-mode timer delay 20
[S3-Vlanif10]vrrp vrid 1 authentication-mode MD5 huawei
Vlanif 20:
Ip address
192.168.20.253/24
Vrrp vrid 2 virtual-ip
192.168.20.254
优先级
xx MD5
密码
xx
配置操作:
[S3-Vlanif10]int vlanif 20
[S3-Vlanif20]ip ad 192.168.20.253 24
[S3-Vlanif20]vrrp vrid 1 virtual-ip 192.168.20.254
[S3-Vlanif20]vrrp vrid 1 priority 150
[S3-Vlanif20]vrrp vrid 2 virtual-ip 192.168.20.1
[S3-Vlanif20]vrrp vrid 2 priority 100
[S3-Vlanif10]vrrp vrid 1 authentication-mode MD5 huawei
SW4
是
PC1 PC7
备份
PC3 PC4
主网关设备
物理地址
虚拟网关地址为:
Vlanif
10
:
Ip address
192.168.10.253/24
Vrrpvrid 1 virtual-ip
192.168.10.254
优先级
xx MD5
密码
xx
操作步骤:
[S4]vlan batch 10 20
[S4-Vlanif10]ip ad 192.168.10.253 24
[S4-Vlanif10]vrrp vrid 1 virtual-ip 192.168.10.254
[S4-Vlanif10]vrrp vrid 1 priority 150
[S4-Vlanif10]vrrp vrid 2 virtual-ip 192.168.10.1
[S4-Vlanif10]vrrp vrid 2 priority 100
[S4-Vlanif10]vrrp vrid 1 authentication-mode MD5 huawei
Vlanif
20
:
Ip address
192.168.20.253/24
Vrrpvrid 2 virtual-ip
192.168.20.254
优先级
xx
关联上行端口并降低优先级
xx MD5
密码
xx
抢占时延
20s
操作步骤:
[S4]vlan batch 10 20
[S4-Vlanif20]ip ad 192.168.10.253 24
[S4-Vlanif20]vrrp vrid 1 virtual-ip 192.168.20.254
[S4-Vlanif20]vrrp vrid 1 priority 150
[S4-Vlanif20]vrrp vrid 2 virtual-ip 192.168.20.1
[S4-Vlanif20]vrrp vrid 2 priority 100
[S4-Vlanif20]vrrpvrid 1 track interface GigabitEthernet 0/0/6 reduced 100
[S4-Vlanif20]vrrp vrid 2 preempt-mode timer delay 20
[S4-Vlanif10]vrrp vrid 1 authentication-mode MD5 huawei
希望大家能够帮忙解决其中的问题,谢谢!!!
有解决方案的朋友可以在评论区回复,我会虚心请教!!!