无线控制器AC上可以有两个管理IP地址，一个在交换模块(sw)上，一个在无线控制模块(ac)上。
开始AC的配置。
划分VLAN以及分配IP地址
[H3C]vlan 2
[VLAN2]quit
[H3C]interface vlan 2
[interface-vlan 2]ip address 1.0.0.1 8
建DHCP服务器：
[H3C]dhcp enable
[H3C]dhcp server ip-pool 1
[dhcp server ip-pool 1]network 1.0.0.0 8
[dhcp server ip-pool 1]gateway-list 1.0.0.1
<H3C>oap connect solt 0 进入交换板视图
[H3C]int Bridge-Aggregation 1
[H3C-Bridge-Aggregation1]port link-type trunk
[H3C-Bridge-Aggregation1]port trunk permit vlan all
<H3C>Ctrl+K 进入AC控制板视图
[H3C]int Bridge-Aggregation 1
[H3C-Bridge-Aggregation1]port link-type trunk
[H3C-Bridge-Aggregation1]port trunk permit vlan all
为了能够帮助自己区分两个视图，不妨给他们分别重命名，命令sw和ac。
由于我们的dhcp对应vlan2，所以需要进去交换板视图，将AP所连接的以太网接口划分到vlan2中去，以保证AP能够顺利获得IP。
[Sw]int g1/0/3
[Sw-gigabitethernet1/0/3]port link-type access
[Sw-gigabitethernet1/0/3]port access vlan 2 //让ap划分到vlan2
[Sw-gigabitethernet1/0/3]quit
[AC]wlan auto-ap enable可以发现AP，我们还需要wlan auto-ap persistent固话AP
[AC]wlan auto-ap persistent name 3891-d5cd-1060 ap4
[AC]wlan auto-ap persistent name 50da-009b-f120 ap2
[AC]wlan auto-ap persistent name 0cda-4126-d340 ap1
[AC]dis wlan ap all
Total Number of APs configured : 3 ---------------------
Total Number of configured APs connected : 3
Total Number of auto APs connected : 0
Total Number of APs connected : 3
Maximum AP capacity : 12
Remaining AP capacity : 9
AP Profiles
State : I = Idle, J = Join, JA = JoinAck, IL = ImageLoad
C = Config, R = Run, KU = KeyUpdate, KC = KeyCfm
M = Master, B = Backup
--------------------------------------------------------------------------------
AP Name State Model Serial-ID
--------------------------------------------------------------------------------
ap4 R/M WA4320-ACN-SI 219801A0T78161E03066
ap2 R/M WA4320i-X 210235A1GSC161002570
ap1 R/M WA2620i-AGN 219801A0CNC132002865
-------------------------------------------------------------------------------
建立无线虚拟接口：
[H3C]interface WLAN-ESS 2
[H3C-WLAN-ESS2]port access vlan 2
创建无线服务模板
[H3C]wlan service-template 2 clear
[H3C-wlan-st-2]ssid your_name
[H3C-wlan-st-2]bind WLAN-ESS 2 绑定无线接口
[H3C-wlan-st-2]authentication-method open-system
[H3C-wlan-st-2] service-template enable
配置射频接口，并绑定无线服务模板
[H3C]wlan auto-ap enable
[H3C]wlan ap 1
[H3C-wlan-ap 1]radio 1
[H3C-wlan-ap 1-radio-1]service-template 2
[H3C-wlan-ap 1-radio-1]radio enable
查看AP注册结果
[H3C]display wlan ap all
步骤5
等注册成功之后，固化AP [H3C]wlan auto-ap persistent all
步骤6
以上步骤做完如果不能注册AP，那么需要检查全部的配置，包括
[AC]dis dhcp server ip-in-use all
Pool utilization: 0.79%
IP address Client-identifier/ Lease expiration Type
192.168.1.2 0cda-4126-d340 Sep 29 2016 16:00:39 Auto:COMMITTED
192.168.1.1 3891-d5cd-1060 Sep 29 2016 16:04:36 Auto:COMMITTED