一、命令详解
ethtool是Linux下用于查询及设置网卡参数的命令。
ethtool [options]
命令选项:
ethtool ethX /
ethtool –h //显示ethtool的命令帮助(help)
ethtool –i ethX //查询ethX网口的相关信息
ethtool –d ethX //查询ethX网口注册性信息
ethtool –r ethX //重置ethX网口到自适应模式
ethtool –S ethX //查询ethX网口收发包统计
ethtool –s ethX [speed 10|100|1000]\ //设置网口速率10/100/1000M
[duplex half|full]\ //设置网口半/全双工
[autoneg on|off]\ //设置网口是否自协商
[port tp|aui|bnc|mii]\ //设置网口类型
二、查看过程
2.1 ifconfig查看网卡信息
[root@master ~]# ifconfig
ens33: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.64.129 netmask 255.255.255.0 broadcast 192.168.64.255
inet6 fe80::b00e:da4d:a946:25c4 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:49:83:af txqueuelen 1000 (Ethernet)
RX packets 53 bytes 5995 (5.8 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 58 bytes 8095 (7.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1 (Local Loopback)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
2.1 ethtool查看网卡带宽
1、[root@master ~]# ethtool ens33
Settings for ens33:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: 1000Mb/s ------------------------------------>网卡速度 ,可知现在是千兆网卡
Duplex: Full
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
MDI-X: off (auto)
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
三、ethtool其他命令选项
1)[root@linux /]# ethtool -i eth1
driver: e1000
version: 5.0.43-k1
firmware-version: N/A
bus-info: 06:08.1
2)[root@linux /]# ethtool -S eth1
NIC statistics:
rx_packets: 58068300
tx_packets: 87124083
rx_bytes: 1589713008
tx_bytes: 2165825901
rx_errors: 0
tx_errors: 0
rx_dropped: 0
tx_dropped: 0
multicast: 0
collisions: 0
rx_length_errors: 0
rx_over_errors: 0
rx_crc_errors: 0
rx_frame_errors: 0
rx_fifo_errors: 0
rx_missed_errors: 0
tx_aborted_errors: 0
tx_carrier_errors: 0
tx_fifo_errors: 0
tx_heartbeat_errors: 0
tx_window_errors: 0
3)[root@linux /]# ethtool -s eth1 autoneg off speed 100 duplex full
相关:
1)[root@linux /]# which ethtool
/sbin/ethtool
2)[root@linux /]# rpm -qf /sbin/ethtool
ethtool-1.6-5
3)怎样使ethtool设置永久保存在网络设备中?
解决方法一:
ethtool设置可通过/etc/sysconfig/network-scripts/ifcfg-ethX文件保存,从而在设备下次启动时激活选项。
例如:ethtool -s eth0 speed 100 duplex full autoneg off
此指令将eth0设备设置为全双工自适应,速度为100Mbs。若要eth0启动时设置这些参数, 修改文件/etc/sysconfig/network-scripts/ifcfg-eth0 ,添加如下一行:
ETHTOOL_OPTS="speed 100 duplex full autoneg off"
解决方法二:
将ethtool设置写入/etc/rc.d/rc.local之中。