条件表达式
文件表达式
if [ -f file ] 如果文件存在
if [ -d … ] 如果目录存在
if [ -s file ] 如果文件存在且非空
if [ -r file ] 如果文件存在且可读
if [ -w file ] 如果文件存在且可写
if [ -x file ] 如果文件存在且可执行
整数变量表达式
if [ int1 -eq int2 ] 如果int1等于int2
if [ int1 -ne int2 ] 如果不等于
if [ int1 -ge int2 ] 如果>=
if [ int1 -gt int2 ] 如果>
if [ int1 -le int2 ] 如果<=
if [ int1 -lt int2 ] 如果<
字符串变量表达式
If [
字符串允许使用赋值号做等号
if [
if [ -n
if [ $sting ] 如果string 非空,返回0 (和-n类似)
条件表达式引用变量要带$
if [ a = b ] ;then
echo equal
else
echo no equal
fi
[macg@machome ~]
改正:
if [
echo equal
else
echo no equal
fi
[macg@machome ~]$ sh test.sh
input a:
5
input b:
5
equal
-eq -ne -lt -nt只能用于整数,不适用于字符串,字符串等于用赋值号=
[macg@machome ~]
then
echo
input your choice:
y
test.sh: line 3: test: y: integer expression_r_r_r expected
期望整数形式,即-eq不支持字符串
=放在别的地方是赋值,放在if [ ] 里就是字符串等于,shell里面没有==的,那是c语言的等于
无空格的字符串,可以加” “,也可以不加
[macg@machome ~]
if [
input a:
123
input is 123
equal123
= 作为等于时,其两边都必须加空格,否则失效
等号也是操作符,必须和其他变量,关键字,用空格格开 (等号做赋值号时正好相反,两边不能有空格)
[macg@machome ~]$ vi test.sh
echo “input your choice:”
read var
if [
echo “input is correct”
else
echo
echo “input your choice:”
read var
if [
echo “input is correct”
else
echo
input your choice:
y
y
input is correct
[macg@machome ~]
input your choice:
no
no
input error
一切正常
If [ $ANS ] 等价于 if [ -n $ANS ]
如果字符串变量非空(then) , 空(else)
echo “input your choice:”
read ANS
if [
input your choice: 回车
empth 说明“回车”就是空串
[macg@machome ~]$ sh test.sh
input your choice:
34
no empty
整数条件表达式,大于,小于,shell里没有> 和< ,会被当作尖括号,只有-ge,-gt,-le,lt
[macg@machome ~]$ vi test.sh
echo “input a:”
read a
if [
input a:
123
3bit
[macg@machome ~]$ sh test.sh
input a:
20
2bit
整数操作符号-ge,-gt,-le,-lt, 别忘了加-
if test $a ge 100 ; then
[macg@machome ~]
[macg@machome ~]$ sh test.sh
input a:
123
3bit
============================逻辑表达式=========================================
逻辑非 ! 条件表达式的相反
if [ ! 表达式 ]
if [ ! -d
逻辑与 –a 条件表达式的并列
if [ 表达式1 –a 表达式2 ]
逻辑或 -o 条件表达式的或
if [ 表达式1 –o 表达式2 ]
逻辑表达式
表达式与前面的= != -d –f –x -ne -eq -lt等合用
逻辑符号就正常的接其他表达式,没有任何括号( ),就是并列
if [ -z “
注意逻辑与-a与逻辑或-o很容易和其他字符串或文件的运算符号搞混了